In short
- The moment of inertia I controls stiffness (deflection), the section modulus S controls elastic stress, and the plastic modulus Z controls the full plastic capacity.
- For built-up shapes, find the centroid first, then add each part's own inertia and its area times the square of its distance from the centroid.
- For an unsymmetric section the top and bottom section moduli are different; the smaller one governs the extreme-fibre stress.
What each property measures
| Property | Symbol and unit | Used for |
|---|---|---|
| Area | A, mm² | axial stress, self-weight, shear area |
| Centroid | ȳ, mm | position of the elastic neutral axis |
| Second moment of area (moment of inertia) | I, mm⁴ | bending stiffness EI, deflection |
| Elastic section modulus | S = I/c, mm³ | extreme-fibre bending stress σ = M/S |
| Plastic section modulus | Z, mm³ | plastic moment Mp = fyZ |
| Radius of gyration | r = √(I/A), mm | slenderness KL/r of columns |
| Torsion constant | J, mm⁴ | twisting stiffness GJ |
Here c is the distance from the neutral axis to the fibre being checked. The moment of inertia depends on the axis: a plank is stiff on edge and floppy when laid flat, because I grows with the cube of the dimension perpendicular to the bending axis.
Basic shapes
| Shape | I about the centroid | S | Z |
|---|---|---|---|
| Rectangle, width b, depth h | bh3/12 | bh2/6 | bh2/4 |
| Solid circle, diameter d | πd4/64 | πd3/32 | d3/6 |
| Box, outside B × H, inside b × h | (BH3 − bh3)/12 | I/(H/2) | (BH2 − bh2)/4 |
The ratio Z/S is the shape factor: 1.5 for a rectangle, 1.7 for a solid circle and about 1.1 to 1.2 for rolled I-sections, which already put most of their material far from the axis.
Built-up sections: the parallel-axis theorem
A T-section, a channel with a plate or a beam with a slab can be split into rectangles. The procedure is:
- Choose a reference line, for example the bottom edge.
- Find the centroid: ȳ = ΣAiyi / ΣAi.
- Add the parts: I = Σ(Ii + Aidi2), where di is the distance from each part's own centroid to the section centroid.
The Ad2 terms usually dominate. Forgetting them, or measuring d from the reference line instead of from the centroid, is the classic error.
Worked example: a welded T-section
Flange 200 × 20 mm on top of a web 20 × 280 mm; total depth 300 mm. Distances are measured from the bottom of the web.
| Part | A (mm²) | y (mm) | Own I (mm⁴) | d (mm) | Ad² (mm⁴) |
|---|---|---|---|---|---|
| Flange | 4000 | 290 | 133 333 | 87.5 | 30 625 000 |
| Web | 5600 | 140 | 36 586 667 | 62.5 | 21 875 000 |
The bottom of the web is twice as far from the neutral axis as the top of the flange, so its stress is twice as high: the bottom modulus governs. The radius of gyration is √(89.2 × 10⁶ / 9600) = 96.4 mm.
Plastic modulus
The plastic neutral axis divides the area into two equal halves of 4800 mm². The flange provides only 4000 mm², so the axis lies in the web, 800/20 = 40 mm below the flange, at 240 mm from the bottom. Taking moments of each area about that axis:
The shape factor Z/Smin = 792/441 ≈ 1.8 is high, as it is for every T-section: much of the elastic reserve sits in the lightly stressed flange.
Units and conversions
- 1 cm⁴ = 10⁴ mm⁴ and 1 cm³ = 10³ mm³. Steel tables often list I in cm⁴, while stresses are computed in N/mm².
- 1 in⁴ = 416 231 mm⁴ = 41.62 cm⁴, and 1 in³ = 16 387 mm³.
- When M is in kN·m and S in cm³, σ in MPa is M × 1000 / S.
Principal axes
For a section with an axis of symmetry, the centroidal axes are also the principal axes and the product of inertia Ixy is zero. Angles and Z-sections have no axis of symmetry: they bend about inclined principal axes, and a load applied vertically also makes them deflect sideways. Their maximum and minimum moments of inertia, I1 and I2, follow from Ix, Iy and Ixy.
HandCalc's section property calculators compute all of these values, including the plastic modulus, the torsion constant and the principal axes, for rectangles and boxes, circles and pipes, triangles and trapezoids, I-sections, channels, angles, T-sections, built-up sections and polygons given by their coordinates. The rectangle and box calculator is free.