In short
- A plate's stiffness is its flexural rigidity D = Et3/12(1 − ν2), the two-dimensional counterpart of EI.
- Results are written as w = αqa4/D and M = βqa2, with a the shorter side; the coefficients depend on the aspect ratio and the edge conditions.
- Beyond an aspect ratio of about 2 a plate carries most of its load the short way, like a one-way slab.
Assumptions of thin-plate theory
The Kirchhoff theory used in HandCalc's plate calculators, and in the classic tables of Timoshenko and Woinowsky-Krieger, assumes that:
- the plate is thin compared with its span (thickness roughly a tenth of the short side or less), so shear deformation can be ignored;
- the deflection is small compared with the thickness, so the middle surface does not stretch;
- the material is linear-elastic, homogeneous and isotropic.
Moments are given per unit width (kN·m/m). Mx is the moment that bends the plate across the short span a, My the one across the long span b.
Coefficients for a simply supported plate
For a plate with all four edges simply supported under a uniform pressure q, the maximum deflection and moments occur at the centre. The coefficients below were computed from the Navier double series with Poisson's ratio 0.3; they agree with the values tabulated by Timoshenko.
| b/a | α (deflection) | β (Mx) | β1 (My) |
|---|---|---|---|
| 1.0 | 0.00406 | 0.0479 | 0.0479 |
| 1.2 | 0.00565 | 0.0627 | 0.0501 |
| 1.4 | 0.00708 | 0.0755 | 0.0502 |
| 1.6 | 0.00831 | 0.0862 | 0.0493 |
| 1.8 | 0.00932 | 0.0948 | 0.0479 |
| 2.0 | 0.01013 | 0.1017 | 0.0464 |
| 3.0 | 0.01223 | 0.1189 | 0.0406 |
| 4.0 | 0.01282 | 0.1235 | 0.0384 |
| ∞ | 0.01302 | 0.1250 | 0.0375 |
The last row is a useful check. As the long side grows without limit, β tends to 1/8, the moment of a simply supported strip of span a, and α tends to 5/384 — the beam result, with EI replaced by D. The moment in the long direction does not vanish: it tends to ν times the short-span moment, because the strip cannot contract sideways freely.
Two-way or one-way?
At an aspect ratio of 2 the short-span moment is already 81 % of the one-way value, and the long-span moment has passed its peak. This is why many concrete codes treat panels with b/a above 2 as one-way slabs and design the long direction only for distribution reinforcement. Square and near-square panels share the load almost equally between the two directions and are the most efficient.
Worked example: a concrete slab panel
The free simply supported plate calculator uses a panel of 3 m × 4.5 m, 200 mm thick, E = 30 000 MPa, ν = 0.2 and q = 10 kN/m²:
The deflection coefficient does not depend on ν (it is already inside D), but the moment coefficients do: with ν = 0.2 they are 0.0784 and 0.0426 instead of the tabulated 0.0812 and 0.0498. The extreme-fibre stress is 6Mx/t2 = 1.06 MPa — an uncracked elastic value, useful as a reference rather than a design figure for reinforced concrete.
Corners lift
A simply supported plate under uniform load does not just sag: its corners try to curl upward. Holding them down takes a concentrated downward force at each corner, R = 0.065 qa2 for a square plate, and the twisting moments near the corners call for top and bottom corner reinforcement in slabs. If the corners are free to lift, the moments at the centre increase.
Other edge conditions
- Clamped edges reduce the centre moment and the deflection but create negative moments along the edges, often larger than the centre moment. For a square plate with all edges clamped, the edge moment is about 0.051 qa2, against 0.023 qa2 at the centre.
- Mixed edges, for example a slab panel continuous on two sides and simply supported on the others, need Lévy series or energy solutions; their coefficients are tabulated separately.
- A free edge changes the behaviour completely: the plate spans towards the supported edges like a cantilever slab.
Limits of the elastic result
Reinforced-concrete slabs crack, creep and redistribute moments, so design codes give their own moment coefficients and deflection rules. Elastic plate theory remains the reference behind those rules and the right tool for steel plates, glass panels, tank walls and for checking finite-element output. If the computed deflection approaches the plate thickness, membrane action becomes important and large-deflection theory is needed.