In short
- Find the support reactions first; every diagram starts from them.
- The slope of the shear diagram equals minus the load intensity, and the slope of the moment diagram equals the shear.
- The largest moment in a span occurs where the shear passes through zero.
Sign convention
The convention used in HandCalc and in most textbooks is:
- Shear force V at a section is positive when the resultant of the forces to the left of the section acts upward.
- Bending moment M is positive when it causes tension in the bottom fibres (sagging) and negative when it causes tension in the top fibres (hogging).
- Distributed load w is positive when it acts downward.
Any consistent convention works, but changing convention halfway through a calculation is the most common source of sign errors. Decide once and write it next to the sketch.
The three relationships
Equilibrium of a short piece of beam gives two differential relationships:
From them follow the rules that let you sketch a diagram without writing an equation for every segment:
- No load on a segment: the shear is constant and the moment varies linearly.
- Uniform load on a segment: the shear varies linearly and the moment is a parabola.
- Point load: the shear jumps by the value of the load; the moment diagram has a kink but no jump.
- Applied couple: the moment jumps by the value of the couple; the shear is unaffected.
- Area rule: the change in moment between two sections equals the area of the shear diagram between them.
The method, step by step
- Draw the free-body diagram with all loads and the unknown reactions. Replace each distributed load by its resultant only for the reaction calculation, never for the diagrams.
- Solve the reactions from ΣFy = 0 and ΣM = 0 about one support. Check them with ΣM = 0 about the other support.
- Mark the key points: supports, the start and end of each distributed load, point loads and applied couples.
- Draw the shear diagram from left to right, starting at zero just left of the beam and following the rules above.
- Locate the zero crossings of the shear; they are the candidate positions of the maximum moment.
- Draw the moment diagram by adding the areas of the shear diagram. At a free end or a pinned end without a couple the moment must return to zero — if it does not, an error has slipped in.
Worked example
A simply supported beam of span 8 m carries a uniform load of 10 kN/m over its whole length and a point load of 40 kN at 2 m from the left support A.
Reactions
Shear
The shear starts at +70 kN at A and falls by 10 kN per metre. Just left of the point load it is 70 − 20 = 50 kN; the point load drops it to 10 kN. It then falls again at 10 kN/m and passes through zero 1 m further on, at x = 3 m. Over the remaining 6 m it loses another 60 kN and reaches −50 kN at B, which is exactly −RB: the diagram closes.
Moment
The moment at 2 m equals the area of the shear diagram from 0 to 2 m: (70 + 50)/2 × 2 = 120 kN·m. From 2 m to 3 m the shear triangle adds 10 × 1/2 = 5 kN·m, so the maximum moment is 125 kN·m at x = 3 m — not at mid-span, because the point load pulls the peak towards it. Beyond 3 m the shear is negative, the moment decreases and it returns to zero at B.
| x (m) | V (kN) | M (kN·m) |
|---|---|---|
| 0 (support A) | +70 | 0 |
| 2 (point load) | +50 / +10 | 120 |
| 3 (shear = 0) | 0 | 125 |
| 5 | −20 | 105 |
| 8 (support B) | −50 | 0 |
Checks that catch most mistakes
- The shear just right of the last support (or at a free end) must be zero.
- The moment at a pinned or free end must be zero unless a couple is applied there.
- The moment is a maximum or minimum only where the shear is zero or changes sign at a point load.
- For a symmetric beam under symmetric load the shear is antisymmetric and the moment symmetric.
- Overhangs and cantilevers produce negative (hogging) moments at the supports; a diagram with only positive moments for an overhanging beam is wrong.
When the hand method stops being practical
Statically indeterminate beams — propped, fixed or continuous — need a compatibility condition before the reactions are known. Once the redundant reactions are found, the same rules draw the diagrams. HandCalc's beam calculators do this for 32 classic cases and plot the shear, moment and deflection along the span; the free simple beam calculator is a good place to compare your own sketch with the computed diagrams.