HCHandCalc

Rectangular Plate, 3 Edges Fixed + 1 Free — Varying Load

Plates · Rectangular · Three Edges Built In, One Edge Free · Linearly Varying (Hydrostatic / Trapezoidal) Load — Kirchhoff Thin-Plate Theory, Ritz Solution
Worked example

This page shows the complete calculation with example values: the inputs, the results and every step in between.

The interactive calculator is part of HandCalc Pro. With Pro you can enter your own values, switch between SI and Imperial units and download the technical report as PDF or Word.

1

Geometry, material and load

a = short side, b = long side (b ≥ a); which edge is free; thickness, E, ν and the pressure at the two ends of the load ramp
m
m
mm
kN/m²
kN/m²
MPa
—
Dflexural rigidity per unit width = E·t³12(1 − ν²) = 20833.33kN·m
b/aaspect ratio = 1.5
Model: Kirchhoff thin plate, three edges built in (w = 0, ∂w/∂n = 0) and one edge free (Mn = 0, Vn = 0), pressure varying linearly from q₁ at the built-in edge opposite the free one to q₂ at the free edge and constant along it (q₁ = 0 or q₂ = 0 gives the hydrostatic triangle, q₁ = q₂ the uniform case); coefficients α, β are referred to qmax = max(q₁, q₂). Solved by the Rayleigh–Ritz method with the full strain energy (the free edge deflects, so the Gaussian-curvature term is kept): clamped–clamped beam modes between the two opposite built-in edges, and across them a clamped-root Chebyshev family ξ²·Tk(2ξ−1) that leaves the free edge unconstrained (16 × 16 terms; built-in edge moments Richardson-extrapolated from the 8- and 16-term solutions). Checked against an independent trial space and the cantilever-strip limits (triangular load: w = 11qb⁴/120D or qb⁴/30D, root moment qb²/3 or qb²/6). Sign convention: w positive downward, M positive when the bottom face is in tension.
2

Deflection

Ritz solution — the maximum is at the middle of the free edge when the load grows toward it; with the heavy end at the root it moves inside the plate
w(x, y) = ΣmΣn cmn·φm(x)·φn(y) φm = clamped–clamped modes (cos λ·cosh λ = 1), ψn = ξ²·Tn(2ξ−1); cmn from δΠ = 0, Π = ½D∫[w,xx² + w,yy² + 2νw,xxw,yy + 2(1−ν)w,xy²] − ∫q(x,y)·w, the load ramp integrated exactly
wmaxat (1.5, 4.5) m — = α·q_max·a⁴/D, α = 0.00244 = 0.095mm a / wmax = 31649
Compare (square, ν = 0.3, three built in + one free): uniform load α = 0.0030 at the free edge; hydrostatic triangle growing toward the free edge 0.0024 (free edge), reversed 0.0008 (inside the plate, the free edge itself only 0.0006). As a/b grows the plate tends to a cantilever strip across b: w → 11qmaxb⁴/120D (root moment qmaxb²/3) for the triangle growing toward the tip, qmaxb⁴/30D (qmaxb²/6) reversed. Thin-plate theory holds while wmax stays below about t/2.
Deflection along the short span — section A–A (y = b/2, 0 ≤ x ≤ a)
0aw = 0.049 mmw(1) = 0.038 mm
Deflection along the long span — section B–B (x = a/2, 0 ≤ y ≤ b)
0bw = 0.095 mmw(2.25) = 0.049 mm
3

Bending moments and stresses

Mx = −D(w,xx + ν·w,yy), My = −D(w,yy + ν·w,xx) — per unit width; the built-in edges govern, the free edge carries a sagging moment along it
Mx,edgebuilt-in edges x = 0 and x = a, peak at y = 4.35 m — hogging, = β_f·q_max·a², β_f = -0.0781 = -7.03kN·m/m
My,edgebuilt-in edge y = 0, peak at x = 1.5 m — hogging, = β_f2·q_max·a², β_f2 = -0.0147 = -1.33kN·m/m
Mfreemiddle of the free edge, parallel to it — sagging, = β_e·q_max·a², β_e = 0.0374 = 3.37kN·m/m
Mx,centre(a/2, b/2), spanning the short side — = β·qmax·a², β = 0.02 = 1.8kN·m/m
My,centre(a/2, b/2), spanning the long side — = β₁·qmax·a², β₁ = 0.0049 = 0.44kN·m/m
σedge= 6·|Medge|/t² — top face in tension at the governing built-in edge = 1.05MPa
σx,centre= 6·Mx/t² = 0.27MPa σy,centre= 6·My/t² = 0.07MPa
Square plate, ν = 0.3, hydrostatic triangle growing toward the free edge: βf ≈ −0.076 on the two opposite built-in edges (peak close to the free end), −0.021 at the root, +0.034 along the free edge; reversed: −0.030, −0.035 and +0.010. Built-in edge moments are Richardson-extrapolated (error ∝ 1/N²); the free-edge quantities converge directly with the Chebyshev family.
Mx along the short span — section A–A (y = b/2, 0 ≤ x ≤ a) — built-in at both ends
0aMx = 1.8 kN·m/mMx = -3.63 kN·m/mMx(1) = 1.21 kN·m/m
My along the long span — section B–B (x = a/2, 0 ≤ y ≤ b) — built-in at y = 0, free at y = b
0bMy = 0.59 kN·m/mMy = -1.33 kN·m/mMy(2.25) = 0.44 kN·m/m
4

Corner forces

Every corner touches a built-in edge — no concentrated corner forces; the free edge carries no reaction
RcornerMxy = 0 along every built-in edge, and each corner lies on one = 0
Edge reactions are not reported for this case — third derivatives of a Ritz expansion are not reliable enough for design; the built-in edges carry the bulk of the load.
5

At a given point

Read w, Mx, My, Mxy anywhere — marked in amber on the diagrams
m
01.5 m3 m
m
02.25 m4.5 m
w= 0.038mm Mx= 1.21kN·m/m
My= 0.3kN·m/m Mxy= -0.31kN·m/m