HCHandCalc

Fixed-Base Portal Frame — Horizontal Point Load at Eave

Frames · Fixed-Base Rectangular Portal · Horizontal Point Load at Eave (B) · Slope-deflection closed-form (sway)
Worked example

This page shows the complete calculation with example values: the inputs, the results and every step in between.

The interactive calculator is part of HandCalc Pro. With Pro you can enter your own values, switch between SI and Imperial units and download the technical report as PDF or Word.

1

Geometry, load and stiffness

Span, column height, horizontal point load at B, and section moments of inertia
m
m
kN
Define separate section inertia / elastic modulus for column and beam
Model: Supports A and D are FIXED (transmit both rotation and translation); joints B and C are rigid. P is applied horizontally exactly at B (left column-beam joint, eave level). This load case is NOT SYMMETRIC (unlike Type 3) — the frame SWAYS sideways; solved with slope-deflection. The two columns are assumed IDENTICAL, which gives H = P/2 (at each support, independent of kr), but Mbase, Mcorner and Rv do depend on kr.
2

Reactions and horizontal thrust

H, Rv
krbeam/column relative stiffness ratio (E·I) = EbIb·hEcIc·ℓ = 2.00e+5×8000×3 / (2.00e+5×8000×6) = 0.5
Hat each support, opposing P — independent of kr = P2 = 50 / 2 = 25kN
Rvat each support, vertical (force couple) = 3kr·Phℓ(1+6kr) = 3×0.5×50×3 / (6×(1+6×0.5)) = 9.38kN
Why H is independent of kr but Rv is not: since the beam is axially rigid and the columns are identical, H = P/2 always holds (same mechanism as in Type 2). But because the fixed bases develop base moments, overturning equilibrium is now shared (partly) between Rv and the base moments — which makes Rv depend on kr. Uplift (tension) on the A side, compression on the D side.
3

Bending moments

Base (Mt) and corner (Mk) moments
Mtbase (A, D) — same magnitude at both = (1+3kr)·Ph2(1+6kr) = (1+3×0.5)×50×3 / (2×(1+6×0.5)) = 46.88kN·m
Mkcorner (B, C) — equal to Rv·ℓ/2 = 3kr·Ph2(1+6kr) = 3×0.5×50×3 / (2×(1+6×0.5)) = 28.13kN·m
The column moment varies LINEARLY from Mt at the base to −Mk at the corner, and typically CHANGES SIGN within the column (inflection point) — a characteristic of swaying frames, unlike the non-sway behavior of Type 1 / Type 3. The beam moment varies linearly between −Mk at B and +Mk at C (same pattern as Type 2), passing through zero at midspan.
Bending Moment Diagram (M) — on the frame
+46.88 kN·m−46.88 kN·m−28.13 kN·m+28.13 kN·mM = 0red: negative · blue: positive — sway: the column may show a sign change (inflection point)
4

Shear and axial force

V, N in the columns and beam — on the frame
Vcolumn (both, constant) · beam (constant, no distributed load) = H · Rv
Ncolumn AB (B side): Rv, tension · column CD (C side): Rv, compression · beam: H, compression = Rv · H
Shear Force Diagram (V) — on the frame
V = 25 kNV = 25 kNV = 9.38 kN (constant)
Axial Force Diagram (N) — on the frame
N = +9.38 kN (tension)N = −9.38 kN (compression)N = −25 kN (compression)