HCHandCalc

Portal Frame — Pinned Base, Horizontal Point Load at Eave

Frames · Two-Hinged Rectangular Portal · Horizontal Point Load at Eave (B) · Force method closed-form
Worked example

This page shows the complete calculation with example values: the inputs, the results and every step in between.

The interactive calculator is part of HandCalc Pro. With Pro you can enter your own values, switch between SI and Imperial units and download the technical report as PDF or Word.

1

Geometry and load

Span, column height and horizontal point load at B
m
m
kN
Define separate section inertia / elastic modulus for column and beam
Model: supports A and D are pinned (no moment transfer); corners B and C are rigid (the beam-column angle stays fixed). P is applied horizontally exactly at B (the left column-beam joint, eave level). The two columns are assumed IDENTICAL (same h, I and E). The beam is assumed axially rigid (inextensible) — together these two assumptions make the results (H, Rv, Mk) entirely INDEPENDENT of section inertia and elastic modulus (see the Reactions card for the reasoning).
2

Reactions and horizontal thrust

H, Rv
Hat each support, opposing P = P2 = 50 / 2 = 25kN
Rvat each support, vertical (force couple) = P·hℓ = 50×3 / 6 = 25kN
krfrom your section inputs — does not appear in the H formula at all = EbIbhEcIcℓ = 0.5
Why it's independent of kr: since the beam is assumed axially rigid (inextensible), B and C undergo the same horizontal displacement — regardless of where P is applied along the beam. Because the two columns are identical (same h, I, E), the horizontal load splits EQUALLY between them: H = P/2, in the same direction at both supports (opposing P). The overturning moment P·h is resisted by an axial force couple spanning ℓ between A and D (Rv = Ph/ℓ) — uplift (tension) on the A side, compression on the D side. Vary kr above as much as you like — H always stays P/2.
3

Bending moments

Corner moment Mk (B, C) — zero at midspan
Mkcorner (B and C) — equal magnitude, opposite sense = H·h = 25 × 3 = 75kN·m
The column moment is zero at the base (pin) and increases linearly to Mk at the corner. In the beam the moment is −Mk at B and +Mk at C — it changes sign at midspan (double curvature). This comes from BOTH beam ends being rotated in OPPOSITE senses by the rigid-corner moment; it differs from a single-sign distribution like wℓ²/8 (which applies to a vertical UDL).
Bending Moment Diagram (M) — on the frame
−75 kN·m+75 kN·mM = 0red: negative · blue: positive — equal magnitude at the corners, opposite sense (double curvature)
4

Shear and axial force

V and N in column and beam — on the frame
Vcolumn (both, constant) · beam (constant, no distributed load) = H · Rv
Ncolumn AB (B side): Rv, tension · column CD (C side): Rv, compression · beam: H, compression = Rv · H
The column axial forces form the force couple that resists the overturning moment: the side where P is applied (AB, the B end) is in TENSION (tends to lift), the opposite side (CD) is in COMPRESSION. The beam is axially COMPRESSED by the shear carried in from each column (N = H, compression) — the shear from one column routes through the corner into the beam axis and back out through the other.
Shear Force Diagram (V) — on the frame
V = 25 kNV = 25 kNV = 25 kN (constant)
Axial Force Diagram (N) — on the frame
N = +25 kN (tension)N = −25 kN (compression)N = −25 kN (compression)