HCHandCalc

Rectangular Plate, All Edges Fixed — Uniform Load

Plates · Rectangular · All Four Edges Built In · Uniform Load q — Kirchhoff Thin-Plate Theory, Ritz Solution
Worked example

This page shows the complete calculation with example values: the inputs, the results and every step in between.

The interactive calculator is part of HandCalc Pro. With Pro you can enter your own values, switch between SI and Imperial units and download the technical report as PDF or Word.

1

Geometry, material and load

a = short side, b = long side (b ≥ a); thickness, E, ν and the uniform pressure q
m
m
mm
kN/m²
MPa
—
Dflexural rigidity per unit width = E·t³12(1 − ν²) = 20833.33kN·m
b/aaspect ratio = 1.5
Model: Kirchhoff thin plate, all four edges built in (w = 0, ∂w/∂n = 0), uniform pressure q. No separable exact series exists, so the plate is solved by the Rayleigh–Ritz method with products of clamped–clamped beam eigenfunctions in both directions (16 × 16 terms; edge moments Richardson-extrapolated from the 8- and 16-term solutions) — checked against a fine finite-difference solution to better than 0.5 % and against Timoshenko's Table 35 (square: α = 0.00126, βf = −0.0513, β = 0.0231). Sign convention: w positive downward, M positive when the bottom face is in tension; the built-in edges carry negative (hogging) moments.
2

Deflection

Ritz solution — doubly symmetric, the maximum is at the centre
w(x, y) = ΣmΣn cmn·φm(x)·φn(y) φm, φn = clamped–clamped beam modes (cos λ·cosh λ = 1: λ = 4.7300, 7.8532, …); cmn from δ[½D∫(∇²w)² − ∫q·w] = 0
wmaxat the centre (a/2, b/2) — = α·q·a⁴/D, α = 0.0022 = 0.085mm a / wmax = 35130
Compare (square, ν = 0.3): all edges simply supported α = 0.00406; one edge built in 0.0028; two opposite 0.00192; two adjacent 0.0022; three built in 0.0016; all four built in 0.00126 — the stiffest case; for b/a ≥ 2 the plate behaves as a fixed-ended strip across a (α → 1/384 = 0.00260). Thin-plate theory holds while wmax stays below about t/2.
Deflection along the short span — section A–A (y = b/2, 0 ≤ x ≤ a)
0aw = 0.085 mmw(1) = 0.068 mm
Deflection along the long span — section B–B (x = a/2, 0 ≤ y ≤ b)
0bw = 0.085 mmw(2.25) = 0.085 mm
3

Bending moments and stresses

Mx = −D(w,xx + ν·w,yy), My = −D(w,yy + ν·w,xx) — per unit width; the midpoints of the long built-in edges govern
Mx,edgelong edges x = 0 and x = a, at y = 2.25 m — hogging, = β_f·q·a², β_f = -0.0757 = -6.81kN·m/m
My,edgeshort edges y = 0 and y = b, at x = 1.5 m — hogging, = β_f2·q·a², β_f2 = -0.0568 = -5.11kN·m/m
Mx,centre(a/2, b/2), spanning the short side — = β·q·a², β = 0.0357 = 3.21kN·m/m
My,centre(a/2, b/2), spanning the long side — = β₁·q·a², β₁ = 0.0168 = 1.51kN·m/m
σedge= 6·|Medge|/t² — top face in tension at the governing built-in edge = 1.02MPa
σx,centre= 6·Mx/t² = 0.48MPa σy,centre= 6·My/t² = 0.23MPa
Timoshenko Table 35 (ν = 0.3): βf = −0.0513 / −0.0757 / −0.0829 at the midpoint of the long edges for b/a = 1 / 1.5 / 2 (limit −1/12 = −0.0833), β = 0.0231 / 0.0368 / 0.0412 at the centre. Edge moments are extrapolated from the 8- and 16-term Ritz solutions (error ∝ 1/N²) and agree with a 120-division finite-difference solution to 0.5 %.
Mx along the short span — section A–A (y = b/2, 0 ≤ x ≤ a) — built-in at both ends
0aMx = 3.21 kN·m/mMx = -6.78 kN·m/mMx(1) = 2.27 kN·m/m
My along the long span — section B–B (x = a/2, 0 ≤ y ≤ b) — built-in at both ends
0bMy = 1.53 kN·m/mMy = -5.02 kN·m/mMy(2.25) = 1.51 kN·m/m
4

Corner forces

All edges built in — no concentrated corner forces
RcornerMxy = 0 along every built-in edge, and each corner lies on one = 0
Edge reactions are not reported for this case — third derivatives of a Ritz expansion are not reliable enough for design; the total load q·a·b is shared by the four built-in edges, the long edges taking the larger part.
5

At a given point

Read w, Mx, My, Mxy anywhere — marked in amber on the diagrams
m
01.5 m3 m
m
02.25 m4.5 m
w= 0.068mm Mx= 2.27kN·m/m
My= 1.13kN·m/m Mxy= 0kN·m/m